New latex layer or new bed? Bryte bed?

Mattress Talk General Mattresses Questions
1

Hello folks,

I purchased a latex bed from Nest Bedding about 10 years ago. The last year or so, it just hasn’t felt as comfortable. I’ve tried flipping layers and that was kinda ok for a short time. However, I am waking up where I know there’'s something with shoulder pressure point sometimes. And it seems like there’s a bit of an indentation or sag.

Other notes

  • I’ve noticed that I often sleep better in hotels than I do at home and so this has made me think that maybe I just need a new bed
  • I’m also waking up in the middle of the night, though I’m not sure if that has to do with the mattress or just age.
  • I’m also a hot sleeper and prefer a cooler sleeping environment so foam or anything that adds to warmer sleep is non optimal

So, questions:

  • Should I just buy new layers or a whole new bed system?
  • I have been looking at the Bryte bed due to its smart bed adjustability features. It’s a lot of $$. But looking at the layers, I’m concerned about the foam and sleeping warmer.

Thank you

2 Likes
2

When a mattress or one of its layers wears out, even an average mattress might seem better than the old one. If your mattress has a zippered top layer, you can reach out to @NestBedding to ask if they offer replacement layers.

After 10 years, you’ve probably gotten your money’s worth from your mattress. It might be a good time to consider getting a new mattress and foundation.

Your current foundation might still be fine, or it might not. After a decade of use, it could be worn down. If it’s starting to bend or flex, it might have caused your old mattress to sag. If you put a new mattress on a weak foundation, it could shorten the life of your new mattress.

In the end, the condition of your foundation may help you decide what to do next.

I am not familiar with the Bryte Bed, but will take a peek at it and report back.

Maverick

3

Thanks, Maverik.

I should have mentioned that I did reach out to Nest and they no longer do replacement layers but they offered me a discount on new bed.

When you say foundation do you mean the frame? If not, there isn’t a foundation later, in the traditional sense. Mattress is sitting on top of slatted frame as is required for latex so it can breathe (is what I understood).

Thanks

1 Like
4

As long as the slats are less than 3" spaced, 2-3" wide and about 3/4" thick or more, and do not flex and are not bowing when you lie on the mattress, then you should be fine.

5

Hey there Dog,

I took some time to review the Bryte Bed website to get a better sense of what the concept is. From what I can tell, it’s a really high-tech mattress that uses a grid of small air cells to adjust to your body while you sleep. These air pockets inflate or deflate depending on how you’re lying, so the bed shifts to support you in real time. It also tracks your sleep, plays relaxing audio to help you fall asleep, and lets both sides of the bed be customized independently. The idea is to give you a more personalized and responsive sleep experience.

But while it’s an interesting concept, I’m not totally convinced it’s practical in the long run. The fact that it relies on dozens of air cells, sensors, and software means there’s a lot more going on under the surface compared to a traditional mattress. Each cell has an air tube connected and relies on all internal components to function.

And with that, there’s more that could potentially break or wear out. A good pocket spring or hybrid mattress might not be as high tech, but it’s simpler, more durable, and easier to maintain. Unless someone really wants a high-tech sleep system or has specific pain or sleep issues it might help with, I think a well-made traditional mattress is probably the more sensible choice for most people.

I will say, I have been testing a Perfectly Snug Smart Topper. I am not adding this into the conversation as a suggestion, but more anecdotal. First it is a topper. If you don’t like it, you simply remove it from the mattress. If you like it and your partner does not, you simply shut one side down. The PS is more of a sensory climate control component whereas the Bryte is a complete sensory system. They don’t actually state what those components are made with. Likely it is some thermoplastic material of some type.

I suppose you have to trust that it’s been put through its paces and thoroughly tested, but you never really know. Sometimes ideas come along that at first seem clever and innovative, and you think, “Okay, that’s pretty cool.” But then after the initial excitement fades, you realize it might not actually make much of a difference for you. Like with most airbed systems. “Oooh, I can adjust the feel to a 75 or an 89. yeah my bed can do that, cool isnt it?” How often to do change the settings? “Never” LOL, end of story.

I’m not usually one to go for gimmicks, but I’m open to trying new things now and then. So if you’re the kind of person who likes exploring new concepts, it could be worth giving it a shot.

Just my two cents.

Maverick

6

Thank you for taking the time, Maverick.

Yes, I started to think the same about Bryte bed. But you know, when you aren’t sleeping anything to help sounds lovely.

I think the frame is ok.

Yes. I saw the Perfectly Snug suggestion in another thread. i’ve tried the Sleep me. 2 generations of it and neither was really perfect. Sitting in garage. Wow. The $$!

Of the mattress materials, Latex is probably the coolest? Or is there some other material I should think about?

Tks

1 Like
7

Latex is a sponge/foam. It retains heat. Not nearly like memory foam. Most folks do not find latex hot to sleep on. There are however a lot of the obvious variables.

Wool and/or horsehair or a combination of the two in a topper is going to be the coolest.

It does not “create” anything, it just facilitaes the passing of heat though it, plus it helps remove any remnants of moisture to maintain a drier environment. Which translates to a cooler sleeping area.

It may sound elementary, but a simple floor fan constantly pointed at the mattress, makes a big difference for $59.95. I put [this one](Ozeri - OZF6 Brezza III Dual… Amazon.com) on my wifes side of the bed. The sound helps her sleep and it keeps any moisture in the room out. Our master bedroom is over the garage, so the insulation sucks.

There is more than one way to get it done. We dont always have to go for the big bucks. Keep it natural, is always better when trying to stay cool.